- #Turbo 350 transmission diagram movie
- #Turbo 350 transmission diagram install
- #Turbo 350 transmission diagram manual
- #Turbo 350 transmission diagram full
#Turbo 350 transmission diagram movie
Release Calendar Top 250 Movies Most Popular Movies Browse Movies by Genre Top Box Office Showtimes & Tickets Movie News India Movie Spotlight. 84 | View Map.Find Avatar: The Way of Water showtimes for local movie theaters. If you are unfamiliar with installing a valve body, consult a transmission specialist.Avatar: The Way of Water showtimes in Winter Park, FL. Installing all new seals, gaskets and filtersħ. Remove vacuum line and kick down cable.Ħ. Removing center seal in direct clutch drum.ģ. When using this valve body you will have a better performance transmission by:ġ.
#Turbo 350 transmission diagram full
Then recheck fluid for correct level. Never fill over the full mark on dipstick. After transmission is warm, run it through all gears. Refill transmission with a brand of type “F” transmission fluid (We recommend BTE 940600 Super Shift Fluid™). Be sure to place gasket between filter and valve body. Check to make sure filter lines up with valve body holes. STEP 14: Replace your old filter with a BTE 358500 filter kit back into your transmission. Tighten valve body and spacer support plate bolts from the middle out. Tighten to 8-10 ft./lbs. Start all bolts making sure valve body is in its proper place. STEP 13: Place valve body to spacer gasket up into place making sure to line up gear shift selector pin.
#Turbo 350 transmission diagram manual
STEP 12: Before installing new valve body, retrieve manual valve from old valve body and place in new one. Make sure spacer support plate has no rough edges. Start all seven (7) bolts in place before tightening start valve body bolts. Place the support plate into position with the factory support plate on top.
#Turbo 350 transmission diagram install
Then install the valve body separator plate, followed by the valve body gasket marked “VB”. STEP 11: Install valve body gasket marked “C” for Case towards the trans case. STEP 10: Place oil pump screen into area marked “C” in Photo 1 using an assembly grease. If this happens, reassemble using Photo 2 as a guide. STEP 9: The front servo will sometimes fall out when removing the spacer plate in Step 6. Be extremely careful! If tapped too hard punch will go straight through the bottom of plug. STEP 8: Using a broad, blunt punch, very carefully tap one (1) of the two (2) plugs contained in this kit into the hole drilled in Step 7. Drill a 19/64” hole in area marked with an “A” in Photo 1 (in some models this hole is already 5/16”). Do not drill hole over 3/4” deep. STEP 7: Remove the governor screen or screens from transmission and discard. See Photo 1. Pontiac, Oldsmobile and Buick have two (2) governor screens in rear case, one (1) in each passage. These screens are located in case underneath the valve body spacer plate. Take notice that the governor screen and oil pump screen does not fall out. There are four (4) small balls sitting on plate, these balls may be discarded. STEP 6: Remove spacer support plate bolts. Do not drop valve body or manual valve with angled shift pin. Carefully lower valve body and at the same time slide angled shift pin lever from gearshift selector. Remove the seventeen (17) bolts from valve body. STEP 5: Take notice of gearshift linkage position before removing valve body. These pieces are no longer needed so may be discarded.
STEP 4: Remove kick down valve wire by pulling pin out of kick down lever in valve body. STEP 3: Remove transmission filter by removing two (2) screws. Caution not to lose gasket. Some GM vehicles without drain plugs must be drained by dropping transmission pan. STEP 2: Remove drain plug and drain fluid. If vehicle is on ground, please secure wheels to avoid rolling. STEP 1: Allow transmission to cool before installation. One (1) Large Valve Body to Spacer Gasket One (1) Small Valve Body to Spacer Gasket Please read instructions completely, then follow each step to install valve body. TURBO 350 FULL MANUAL VALVE BODY FORWARD SHIFT PATTERN (P-R-N-3-2-1)
0 kommentar(er)
